Thread pneumatic angle seat valve

Body material	SS304,SS316,SS316L
Core material	SS304,SS316,SS316L
Seal mateiral	PTFE, F46
Nominal pressure	PN16KG
Connection type	Thread
Control type	Single acting, double acting
Pnematic actuator material	Polyamide PA, stainless steel
Pneumatic accessory	Solenoid valve, limit switch box, positioner, handle wheel, etc

Product parametersSize chartActuator working princile

Standard technical parameters

Body material:304、316、316L

Spool material: 304、316、316L

Seat material: PTFE、F46

Applicable temperature: PTFE:-30℃～180℃

F46: -30℃～220℃ Actuator must be used stainless steel material

Ambient temp.:-30℃～80℃

Nominal pressure: 1.6Mpa

Connection type: Thread DN10-DN80

Flange: DN15-DN100

Clamp: DN15-DN80

Welding: DN15-DN80

Design standards: GB、ANSI、DIN、ISO

Control type: Single acting, air to open type

Single acting, air to close type

Double acting

Actuator material: Polyamide PA, stainless steel

Optional accessory: Solenoid valve, limit switch box, positioner, etc.

Size	Inch	Inner diameter	Kv Value	The max. pressure differential	Air supply	The cylinder bore	Flow direction
Size	Inch	Inner diameter	Kv Value	The max. pressure differential	Air supply	The cylinder bore	Flow direction
DN10	3/8’	10	3.7	0-16bar	4-7bar	50	Steam, gas, Flow above seat
DN15	1/2’	15	4.2			50
DN20	3/4’	20	8.0			50
DN25	1’	25	19.0			63
DN32	1-1/4’	32	27.5			63
DN40	1-1/2’	40	42.0			63	Liquids, gas Water hammer-free Flow below seat
DN50	2’	50	55.0			80
DN65	2-1/2’	65	90			100
DN80	3	80				100
DN100	4	100				125

NO	1	2	3	4
Name	Positioner	Limit switch	Switch prompt feedback	Solenoid valve
Input signal	4-20Ma, 0-5v, 1-10v			AC220V; DC24V
Output signal	Optional: 4-20mA, 0-5v, 1-10v	Built-in two passive contact switch	Built-in float switch
Function	The remote flow control, temperature control	Feedback valve open and closed postion	Site operation beservation	Solenoid valve losing and get electricity, control the air reversing, realize the pneumatic valve switch.

Pneumatic angle seat valve

Thread connection size drawing:

Type specification table:

Size	Inch	Thread type					Weight
Size	Inch	L	L1	D	H	L2	Weight
DN10	3/8’	135	65	G3/8	110	53	0.8
DN15	1/2’	173	85	G1/2	137	64	1.0
DN20	3/4’	178	95	G3/4	145	64	1.1
DN25	1’	210	105	G1	185	80	1.45
DN32	1-1/4’	220	120	G1-1/4	185	80	2.55
DN40	1-1/2’	228	130	G1-1/2	185	80	4.5
DN50	2’	268	150	G2	215	100	6.3
DN65	2-1/2	282	185	G2-1/2	300	126	13.5
DN80	3	368	220	G3	340	126

Control mode:

According to the site condition has the following three kinds of control mode, the reasonable selection of the control method can make your valves service life more longer, more convenient operation, cost savings.

Normally open type user: Suitable for pneumatic valve in the working time longer occasion. When the valve is normally open spring does not load external gas source thrust, then the valve fatigue to a minimum. Because it is by the air pressure to close valve, so need filed air pressure stability, air supply reliable.

Normally closed type user: Suitable for pneumatic valve is in the closed time working longer occasion. For depends on the spring to close, when air pressure to drive the piston push spring, valve open. So for the normally closed user this valve service life more long, gas more economical. At the same time when the air supply fails, the valve is in the closed state, this control state is the most widely used.

Double acting type user: Double acting type refers to the two chambers can be input compressed air separately, realize the two-way movement of the cylinder, no spring in the cylinder, the valve opening and closing rapidly, and can be used for large stroke valve, because it is by air pressure to close valve, so need the field gas source stability, air supply reliable.